• INVESTIGATION INTO FROTH FLOTATION FOR THE BENEFICIATION OF PRINTED CIRCUIT BOARD COMMINUTION FINES 

  Iyiola, Olatunji Ogunniyi (FEDERAL UNIVERSITY OF TECHNOLOGY AKURE, ONDO STATE, NIGERIA, 2009-09)

  In resource recovery from end-of-life printed circuit board (PCB), the physical processing route is considered most environmentally friendly. The-75µm fraction generated-during the comminution assays well above many precious ...
• EFFECTS OF THERMOMECHANICAL PROCESSING ON THE MICROSTRUCTURE, TENSILE STRENGTH AND PLASTICITY INDICES OF 6063 ALUMINIUM ALLOY 

  OMOTOYINBO, JOSEPH AJIBADE (FEDERAL UNIVERSITY OF TECHNOLOGY AKURE, ONDO STATE, NIGERIA, 2008-02)

  An investigation has been carried out on the effect of the variation of thermomechanical processing parameters on the microstructure, tensile strengths and plasticity indices of 6063 Aluminium alloy. It is intended to ...
• DEVELOPMENT OF AUSTEMPERED DUCTILE IRON FOR AUTOMOBILE AND MACHINE PARTS 

  ADEWUYI, BENJAMIN OMOTAYO (FEDERAL UNIVERSITY OF TECHNOLOGY AKURE, ONDO STATE, NIGERIA, 2002-11)

  An investigation has been carried out on the effect of silicon level on austempered ductile iron in order to determine the suitability of the material in the development of structural materials that can be used in the ...
• THE EFFECT OF SURFACE FINISH ON THE EFFICIENCY OF INHIBITORS FOR STEELS CORRODING IN 3% NACL 

  OKPALA, ALEXANDER NWACHUKWU (FEDERAL UNIVERSITY OF TECHNOLOGY AKURE, ONDO STATE, NIGERIA, 1997-01)

  Investigations were carried out to study the effects of surface finish on the efficiency of inhibitors for Steels Corroding in 3 % NaCl. This study was carried out owing to its importance in the drive towards curtailing ...
• THE EFFECT OF HEAT TREATMENT ON THE MICROSTRUCTURE AND THE CORROSION PROPERTIES OF GREY CAST IRON 

  ALUKO, FASAKIN ISRAEL (FEDERAL UNIVERSITY OF TECHNOLOGY AKURE, ONDO STATE, NIGERIA, 1998-08)

  Investigations were carried out to study the effect of heat treatment on the microstructures and the corrosion properties of Grey cast iron. This study was carried out to determine a suitable heat treatment process which ...
• THE EFFECT OF HEAT TREATMENT ON CORROSION AND STRESS CORROSION CRACKING OF CARBON STEEL IN AGRO-FLUIDS 

  ODESHI, AKINDELE GABRIEL (FEDERAL UNIVERSITY OF TECHNOLOGY, AKURE, ONDO STATE, NIGERIA, 1994-03)

  The effect of heat treatment, extraneous ions addition, cathodic and anodic polarisation on corrosion and stress corrosion cracking (SCC) of medium carbon steel in cassava fluid, tomato and pepper juices has been investigated. ...
• SYNERGISTIC EFFECTS OF INHIBITORS AND HEAT TREATMENT ON CORROSION BEHAVIOUR OF MILD STEEL IN SALINE ENVIRONMENT 

  ADUBUOLA, FEMI KOLAWOLE (FEDERAL UNIVERSITY OF TECHNOLOGY, AKURE ONDO STATE, NIGERIA, 2009-04)

  The synergistic effects of alanine, methionine and glutamic acid inhibitors and heat treatment, as a function of weight loss on the corrosion bahaviour of mild steel in the presence of 3% KCI were investigated. The corrosion ...
• STUDIES ON BLEND DESIGN FOR ENHANCING COKEABILITY OF LAMZA COAL 

  ADELEKE, OSENI ADEWALE (FEDERAL UNIVERSITY OF TECHNOLOGY, AKURE, ONDO STATE, NIGERIA, 2004-09)

  The bituminous prime coking coal with plastic properties suitable for metallurgical cokemaking constitutes only about 5% of the world's known coal reserve. In Nigeria, Lafia coal with intolerable ash and sulphur content ...
• RECRYSTALLIZATION STUDIES OF A LOW ALLOY STEEL IN THE (a +y) PHASE REGION 

  ALANEME, KANAYO KENNETH (FEDERAL UNIVERSITY OF TECHNOLOGY, AKURE, ONDO STATE, NIGERIA, 2002-08)

  An investigation of the technical viability of alloy development via thermomechanical processing, in steels, has been undertaken; by: a systematic study of the recrystallization kinetics in a low alloy steel in the (a+y) ...
• MODELS FOR PREDICTING THE MECHANICAL PROPERTIES OF ROLLED RIBBED MEDIUM CARBON STEEL 

  ADEBAYO, ABDULLAHI OLAWAL (FEDERAL UNIVERSITY OF TECHNOLOGY, AKURE, ONDO STATE, NIGERIA, 2010-12)

  The impact toughness; tensile properties- tensile strength at maximum load, tensile strength at break and yield strength; as well as hardness property of medium carbon steels rolled from inland rolling mills (Ajaokuta Steel ...
• MICROSTUCTURES AND MEHCANICAL PROPERTIES OF WELDED COLD- ROLLED LOW- CARBON STEEL PLATE 

  KUTELU, BOLARINWA JONHSON (FEDERAL UNIVERSITY OF TECHNOLOGY, AKURE, ONDO STATE, NIGERIA, 2007-03)

  Low-carbon steels have as one of their properties good weldability as a result they are often joined--into useful structures by welding, however their safe use under different operating conditions is to a large extent ...
• FAILURE ANALYSIS OF NIGERIAN AIR FORCE BEETLE (ABT-18) NOSE WHEEL STRUT 

  OLORUNLEKE, OLUFUNMILAYO (FEDERAL UNIVERSITY OF TECHNOLOGY, AKURE, ONDO STATE, NIGERIA, 2009-12)

  This research centres on failure analysis of the nose wheel strut of the Nigerian Air Force trainer aircraft, ABT-18, which collapsed especially during hard landings. Visual examination with the unaided eye and fractography ...
• EVALUATION OF THE SUITABILITY OF WARM WATER FOR INTERRUPTED QUENCHING OF DUCTILE CAST IRONS 

  BARNABAS, ABEL ADEIZA (FEDERAL UNIVERSITY OF TECHNOLOGY, AKURE, ONDO STATE, NIGERIA, 2011-03)

  The Evaluation of the suitability of warm water for interrupted quenching of ductile cast irons was carried out. The interrupted quenching process was carried out by austenitizing at 850°C for 30minutes, quenching in warm ...
• EFFECTS OF HEAT TREATMENT ON THE MECHANICAL PROPERTIES AND CORROSION BEHAVIOUR OF 5SP ROLLED STEEL 

  DARAMOLA, OLUYEMI O. (FEDERAL UNIVERSITY OF TECHNOLOGY, AKURE, ONDO STATE, NIGERIA, 2009-04)

  Investigations were carried out to study critically the effect of heat- treatment on the mechanical properties and corrosion behaviour of 5sp rolled steel products. The steel was heated to a temperature of 830°C to completely ...
• EFFECTS OF FLUCTUATING HEAT TREATMENT OPERATIONS ON CORROSION RESISTANCE OF AUSTENITIC STAINLESS STEEL SAMPLE IN SULPHURIC ACID SOLUTION 

  OLORUNTOBA, DANIEL TOYIN (FEDERAL UNIVERSITY OF TECHNOLOGY, AKURE, ONDO STATE, NIGERIA, 2002-12)

  Corrosion performances of austenitic stainless steel subjected to various cyclic heat treatment operations of normalisation, annealing and solution-quenching have been evaluated. Samples of the as-received material (hot-rolled ...
• EFFECT OF CARBON CONTENT ON GRAIN REFINEMENT THROUGH THERMAL CYCLING IN PLAIN CARBON STEEL 

  ADEBIYI, DAMILOLA ISAAC (FEDERAL UNIVERSITY OF TECHNOLOGY, AKURE, ONDO STATE, NIGERIA, 2006-08)

  The work investigated the grain refinement achievable In carbon steels by re austenitization and alternate thermal cycling treatments and the properties developed in these carbon steels after cycling at different austenitizing ...
• ECONOMIC ASSESSMENT OF MINING TECHNIQUES OF BARYTES DEPOSITS AT AZARA, NASARAWA STATE 

  SALATI, LUQMAN KAREEM (FEDERAL UNIVERSITY OF TECHNOLOGY, AKURE, ONDO STATE, NIGERIA, 2010-07)

  This research work presents the economic assessment of mining techniques practiced on veins 1 and 17 of Azara barytes deposits in Nasarawa State. The mechanized, semi mechanized and artisanal mining techniques were appraised ...
• DEVELOPMENT OF RAMMING MASS FROM INDIGENOUS REFRACTORY MATERIALS FOR LINING MELTING FURNACES 

  OLASUPO, OLAYODE ADESOLA (FEDERAL UNIVERSITY OF TECHNOLOGY, AKURE, ONDO STATE, NIGERIA, 2003-09)

  Aluminosilicate developed refractory ramming masses for lining melting furnaces were from suitable indigenous raw materials. Chemical analyses of the raw materials were done using the Atomic Absorption Spectrophotometer ...
• DEVELOPMENT OF A LABORATORY BENCH-TOP ELECTRIC HEATING FURNACE 

  OGUNNIYI, Iyiola Olatunji (FEDERAL UNIVERSITY OF TECHNOLOGY, AKURE, ONDO STATE, NIGERIA, 2003-09)

  The development of indigenous furnace technology is vital to the Nigerian engineering industry. Existing efforts have developed hydrocarbon fuel fired types such as crucible and rotary furnaces, but with concomitant problems ...
• DEVELOPMENT OF CEMENTING MATERIALS USING LOCALLY AVAILABLE RAW MATERIALS FOR BUILDING CONSTRUCTION 

  APATA, AYODEJI OLUWATOYIN (FEDERAL UNIVERSITY OF TECHNOLOGY, AKURE, ONDO STATE, NIGERIA, 2003-08)

  In producing cement, all the ingredients but gypsum is sourced locally. To conserve funds used in the importation of gypsum and to proffer solution to the environmental degradation posed by the dumping of rice husk in the ...

View more